屏幕显示和含义
INITIALIZE 提示仪器正在机械初始化WARMUP 提示温度和光学系统正在稳定STANDBY 提示仪器处于准备状态
MEASURE START 提示仪器处于分析开始状态 MEASURE-1
NO MORE SAMPLE 提示正在吸取最后一个架子样本MEASURE-2
R1 DISPENSE FINISHED 提示所有的测试R1试剂分配完毕MEASURE-3
CUVETTE WASH AFTER MEASUREMENT START 提示样本分析完成，反应杯开始冲洗MEASURE-4MEASURE END PROCESS 提示样本分析结束，反应杯冲洗结束STANDBY
MEASURE END 提示样本分析结束，反应杯冲洗结束MEASURE模式的STANDBYMOVING TO STOP 提示进入停止状态，根据子报警具体分析可能的故障MOVING TO PAUSE 提示进入暂停状态，按START键可以继续操作PAUSE 提示目前为暂停状态
STOP 提示目前为停止状态，一般是电脑或机械故障导致，排除故障后再启动SYSTEM END PROCESS 提示系统进程结束，处于关机状态W1 START 提示W1操作开始W1 END 提示W1操作结束W2 START 提示W2操作开始W2 END 提示W2操作结束
PHOTOCAL START 光度校正开始PHOTOCAL END 光度校正结束
ONE-TOUCH MODE ANALYSIS (aaaa) (Profile No. bb)REMOVE RACK FROM RACK FEEDERCHANGE INDEX
ILLEGAL CONSTRUCTION (n)POWER ON
THE SAME SAMPLE ID ALREADY REQUISITIONED (aaaa)样本编号已经申请（样本编号）NOT ALLOWED TO DELETE SAMPLE (aaaaa) 不能删除样本（样本编号）
NOT ALLOWED TO DELETE REPEAT SAMPLE (aaaa) 不能删除重测样本（样本编号）ALREADY REQUISITIONED REPEAT SAMPLE (aaaa) 重测样本已经申请（样本编号）ALREADY MEASUREMENT STARTED (aaaaa) 标准品或试剂空白已经测量（样本编号）PRINTER NOT AVAILABLE 打印机不可用（忙）
Part of data is not output yet 部分数据尚未输出。分析上位完成，不能打印，或DPR STATUS--SYSTEMSTATUS ICON--F4选择尚未打印的数据Ordering 不能切换模式，重新启动分析仪
R1 LOT NO. DIFFERENT FROM RB (aa-bbbbb) c R1试剂空白的批号与试剂瓶的批号不同，重新执行新批号的试剂空白。(位置号-测试名称)c：(None：血清；U:尿液；X：其它)
R2 LOT NO. DIFFERENT FROM RB (aa-bbbbb) c R2试剂空白的批号与试剂瓶的批号不同，重新执行新批号的试剂空白。
R1 LOT NO. DIFFERENT FROM CAL (aa-bbbbb) c R1试剂校准的批号与试剂瓶的批号不同，重新执行新批号的校准。
R2 LOT NO. DIFFERENT FROM CAL (aa-bbbbb) c R2试剂校准的批号与试剂瓶的批号不同，重新执行新批号的校准。
R1 DIFFERENT LOT NO. (aaaaa) R1更换试剂后，所有试剂瓶批号都相同（测试名称）R2 DIFFERENT LOT NO. (aaaaa) R2更换试剂后，所有试剂瓶批号都相同（测试名称）
REAGENT ID READ ERROR (aa) 试剂条码错误（1-76）。错误码是1；过期数据；项目名称为？？？？。检查条码和试剂放置。
REAGENT ID NOT DEFINED (aa) 试剂条码不准确（1-76）。擦干净条码标签，正确放置试剂瓶。
ILLEGAL REAGENT POSITION (aa) 试剂位置不合法（1-76）。试剂容量检查时发现条码标签与输入项目不符ILLEGAL BOTTLE SIZE (aa) 瓶规格不合法（1-76）。
NO REPLY FROM ANL (aa,bb) ANL无应答（信息，信息第一个字节）。系统转为停止模式，重新启动系统。ILLEGAL FLOPPY DISK 软盘不合法。插入正确规格的软盘或重新插入。NO DATA IN FLOPPY DISK 软盘内没有数据。
NO AREA IN FLOPPY DISK 写入失败，软盘容量不够。
ONLINE ERROR (aa) (bbbbbbbbb-ccccc-dd) 联机错误（错误类型）（出错文本-架编号-杯位置）ONLINE ERROR [aa] [bbbbbbbbb] 联机错误（错误类型）[出错文本]
ONLINE FORMAT ERROR (aaaaaa-bbbbb-cc : NO SAMPLE No.) 联机格式错误（发送样本类型和样本标号-架编号-杯位置号）
ONLINE FORMAT ERROR (aaaaaa-bbbbb-cc : NO SAMPLE ID) 联机格式错误（发送样本类型和样本标号-架编号-杯位置号）
21352136213721382139214021412142214321442145214621472151215222012202220322042205220622072208220922102211221222132214221522162217221822192220
ONLINE ILLEGAL TEXT CODE (aaaaaa-bbbbb-cc : dd) 非法文本代码（发送样本类型和样本标号-架编号-杯位置号：接收到的文本）
ONLINE ILLEGAL TEXT BLOCK No. (aaaaaa-bbbbb-cc : dd->ee) 非法文本块编号（发送样本类型和样本标号-架编号-杯位置号：先前接收的块识别码-最后接收的块识别码）
ONLINE ILLEGAL SAMPLE No. (aaaaaa-bbbbb-cc : dddddd) 非法样本编号（发送样本类型和样本标号-架编号-杯位置号：接收到的样本类型和编号）
ONLINE ILLEGAL RACK No. (aaaaaa-bbbbb-cc : ddddd-ee) 非法架编号（发送样本类型和样本标号-架编号-杯位置号：接收到架编号-杯位置号）
ONLINE ILLEGAL SAMPLE KIND (aaaaaa-bbbbb-cc : dd) 非法样本种类（发送样本类型和样本标号-架编号-杯位置号：接收到样本种类）
ONLINE ILLEGAL GENDER TEXT (aaaaaa-bbbbb-cc : d) 非法性别文本（发送样本类型和样本标号-架编号-杯位置号：接收到的性别）
ONLINE ILLEGAL AGE/MONTH (aaaaaa-bbbbb-cc : ddd ee) 非法年龄（发送样本类型和样本标号-架编号-杯位置号：接收到的年龄）
ONLINE ANALYSIS METHOD MISMATCH (aaaaaa-bbbbb-cc : dd <> ee) 分析方法不匹配（发送样本类型和样本标号-架编号-杯位置号：样本类型<>接收到的样本类型）
ONLINE SAMPLE No. MISMATCH (aaaaaa-bbbbb-cc <> dddddd) 样本编号不匹配（发送样本类型和样本标号-架编号-杯位置号<>接收到的样本类型和编号）
ONLINE RACK No. MISMATCH (aaaaaa : bbbbb-cc <> ddddd-ee) 架编号不匹配（发送样本类型和样本标号-架编号-杯位置号<>接收到的架编号-杯位置号）
ONLINE MISMATCH (aaaaaa-bbbbb-cc : ddddddddd <> eeeeeeeee) 联机不匹配（发送样本类型和样本标号-架编号-杯位置号：发送的样本编号<>接收到的样本编号）
ONLINE TEST ITEM ERROR (aaaaaa-bbbbb-cc) 联机测试项目错误（发送样本类型和样本标号-架编号-杯位置号）
ONLINE REPEAT ITEM ERROR (aaaaaa-bbbbb-cc : dddddd) 联机重测项目错误（发送样本类型和样本标号-架编号-杯位置号：样本类型和原始编号）DTR SET ERROR DTR设置错误
DSR CHECK TIMEOUT DSR检查超时
ANL Communication Overrun First Time Error (aa,bb,c) ANL通讯首次超速错误（信息编号，错误编号，再试编号）
ANL Communication Parity First Time Error (aa,bb,c) ANL通讯首次奇偶校验错误（信息编号，错误编号，再试编号）
ANL Communication Framing First Time Error (aa,bb,c) ANL通讯首次框架错误（信息编号，错误编号，再试编号）
ANL Communication other SIO First Time Error (aa,bb,c) ANL通讯首次其他SIO错误（信息编号，错误编号，再试编号）
ANL Communication ENQ sent First Time Error (aa,bb,c) ANL通讯首次ENQ发送错误（信息编号，错误编号，再试编号）
ANL Communication NAK Receive First Time Error (aa,bb,c) ANL通讯首次NAK接收错误（信息编号，错误编号，再试编号）
ANL Communication Timeout First Time Error (aa,bb,c) ANL通讯首次超时错误（信息编号，错误编号，再试编号）
ANL Communication Not Receive STX First Time Error (aa,bb,c) ANL通讯首次无STX接收错误（信息编号，错误编号，再试编号）
ANL Communication Receive Text length not equal First Time Error (aa,bb,c) ANL通讯首次接收文本超长错误（信息编号，错误编号，再试编号）
ANL Communication Receive Illegal ETX Location First Time Error (aa,bb,c) ANL通讯首次ETX位置不合法（信息编号，错误编号，再试编号）
ANL Communication BCC First Time Error (aa,bb,c) BCC首次错误（信息编号，错误编号，再试编号）ANL Communication Text Code First Time Error (aa,bb,c) 文本码首次错误（信息编号，错误编号，再试编号）
ANL Communication Text Sending Char Receive First Time Error (aa,bb,c) 文本发送字符接收首次错误（信息编号，错误编号，再试编号）
ANL Communication Overrun Error (aa,bb,c) 超速错误（信息编号，错误编号，再试编号）ANL Communication Parity Error (aa,bb,c) 奇偶错误（信息编号，错误编号，再试编号）ANL Communication Framing Error (aa,bb,c) 框架错误（信息编号，错误编号，再试编号）ANL Communication other SIO Error (aa,bb,c) 其他SIO（信息编号，错误编号，再试编号）ANL Communication ENQ send Error (aa,bb,c) ENQ发送（信息编号，错误编号，再试编号）ANL Communication NAK Receive (aa,bb,c) NAK接收（信息编号，错误编号，再试编号）ANL Communication Timeout Error (aa,bb,c) 超时（信息编号，错误编号，再试编号）
2221ANL Communication Not Receive STX (aa,bb,c) 无接收STX（信息编号，错误编号，再试编号）
ANL Communication Receive Text length not equal (aa,bb,c) 接收文本长度不相等（信息编号，错误编2222
号，再试编号）
ANL Communication Receive Illegal ETX Location (aa,bb,c) 接收ETX位置不合法（信息编号，错误编号，再2223
试编号）
2224ANL Communication BCC Error (aa,bb,c) BCC错误（信息编号，错误编号，再试编号）
2225ANL Communication Text Code Error (aa,bb,c) 文本码错误（信息编号，错误编号，再试编号）
ANL Communication Text Sending Char Receive Error (aa,bb,c) 文本发送字符接收错误（信息编号，错误编2226
号，再试编号）
2251 PRINTER NOT SELECTED 打印机没有选择2301 NO FLOPPY DISK 无软盘
2302 FLOPPY DISK READ/WRITE ERROR 软盘读写错误3103 POWER FAILURE DETECTED 探测到电源失败
PHOTOMETER CPU INITIAL ERROR (aa) 光度计CPU初始化错误（详细错误）HEX 0位：ROM校验错误，1位：SRAM3104
不能读写数据；2位：错误发生在ARCHNET；3位：OPMC错误
3105 COM. CONTROL CPU INITIAL ERROR (aa) 通讯控制CPU初始化错误（HEX）
OPTICAL COM. MASTER INITIAL ERROR (aa,bb,cc) 光纤主站错误是错误（HEX详细错误，主站错误位置，主站3106
错误状态）
3107 OPTICAL COM. SLAVE INITIAL ERROR (aa) 光纤从站错误是错误（HEX详细错误）3108 PHOTOMETER CPU -> ANL COM. ERROR (aa,bb,cc,dd) 光度计CPU到ANL通讯错误
3109 PHOTOMETER CPU -> ANL TEXT NOT RECEIVED (aa,bb,cc,dd) 光度计CPU到ANL通讯无接收文本3110 ANL -> PHOTOMETER CPU COM. ERROR (aa,bb,cc,dd) ANL到光度计通讯错误3111 PHOTOMETER CPU ERROR (aa,b) 光度计CPU错误3112 OPTICAL COM. ERROR (aa,bb,cc,dd) 光纤通讯错误3113 OPMC ERROR (aa,bb,cc) 光纤连接器错误
3114 ANL -> COM. CONTROL CPU I/F ERROR (aa) ANL-光纤通讯控制CPU错误3115 ANL -> BAR CODE READER COM. ERROR (aa,bb) ANL-条码阅读器通讯错误3116 ANL <- BAR CODE READER COM. ERROR (aa,bb) ANL-条码阅读器通讯错误3118 ANL <- DPR COM. ERROR-1 (aa,bb) ANL-DPR通讯错误3119 ANL <- DPR TEXT NOT RECEIVED (aa) ANL-DPR无接收文本3121 ANL -> DPR COM. ERROR (aa,bb) ANL-DPR通讯错误
3122 RACK/SAMPLE ID READ ERROR (aa) 架/样本条码读取错误（1位：字符检查错误；2位：条码位数错误）
STAT SAMPLE ID READ ERROR (aa) 急诊样本条码读取错误（0：规定时间内读取没有完成；1：字符检查错3123
误；2：条码位数错误）
3124 RACK ID READ ERROR (aa,bb) 架条码错误3127 REAGENT ID READ ERROR (aa) 试剂条码错误3129 ORIGINAL DETERGENT B EMPTY 浓缩清洗剂B空3130 ORIGINAL DETERGENT A EMPTY 浓缩清洗剂A空3131 DETERGENT B SHORT 清洗剂B缺少3132 DETERGENT A SHORT 清洗剂A缺少3133 DI WATER SHORT 去离子水缺少3134 DI WATER EMPTY 去离子水空
3135 DETERGENT B OVERFLOW 清洗剂B溢出3136 DETERGENT A OVERFLOW 清洗剂A溢出3137 DI WATER OVERFLOW 去离子水溢出
3138 REAGENT REF. COVER OPEN 试剂仓盖打开
3140 INCUBATION. BATH/REAGENT REF. TMP. A/D ERROR 反应盘/试剂仓温度A/D转换错误3141 LAMP OFF 灯泡关闭3142 LAMP DARK 灯泡太暗
3143 PHOTOMETER DATA ERROR (aa) 光度计数据错误3144 NO VACUUM PRESSURE 无负压3145 VACUUM TANK FULL 负压罐满
3146 RACK DETECTED ON FEEDER BELT (aa) 步进皮带上有架子
3147 RACK DETECTED ON RERUN FEEDER BELT (aa) 重测步进皮带上有架子3149 RACK RECEIVER FULL 架满3150 NO RACK 无架
3151 NO STAT CUP 无急诊杯
3152 NO SAMPLE PROBE DETERGENT (aa) 无样本针清洗剂3153 REAGENT PROBE DETERGENT SHORT 试剂针清洗剂太少3155 RACK CLASS ERROR 架类型错误
315731603161316231633164316531663167316831693171317231733174317531763177317831793180318131823183318431853187319531963197320132023203320432063212321332143215321632173218322032223232323732383253325432553256325732583259326032613262326432663267 SAMPLE INFORMATION UNMATCH (aa,bbbb,cc,dd,eeeee) 样本信息不匹配 ACAL INCOMPLETE ACAL未完成 QC INCOMPLETE 质控不完整
RB/ACAL SAMPLE PROHIBITED 人工急诊试剂空白/ACAL中断
AUTOMATIC REPEAT ILLEGAL RACK No. (aa,bbbbbbb) 自动重测架号不合法 AUTOMATIC REPEAT RACK OVER 自动重测架结束
SAMPLING POSITION, RACK STEP DISABLED T (aa) 吸样位置，架步进无效 RACK SUPPLIER ERROR T (aa,bb,cc) 架进给错误 RACK BUFFER ERROR T (aa,bb,cc) 架缓冲错误
CPU DETECTION POSITION, RACK STEP UNIT ERROR T (aa,bb,cc) CPU监测位置、架步进单元错误 SAMPLING POSITION, RACK STEP UNIT ERROR T (aa,bb,cc) 吸样位置，架步进单元错误 SAMPLING POSITION, RACK JAM T (aa) 吸样位置，架卡住 RACK BUFFER JAM T 架缓冲卡住 RACK RECEIVER JAM T 架接收卡住
RACK RECEIVER UNIT ERROR T (aa,bb,cc) 架接收单元错误 STAT TABLE ERROR T (aa,bb,cc) 急诊盘错误
SAMPLE PROBE UP/DOWN ERROR T (aa,bb,cc) 样本针上下错误 SAMPLE PROBE ROTATION ERROR T (aa,bb,cc) 样本针摆动错误 SAMPLE DISPENSER ERROR T (aa,bb,cc) 样本分配错误
SAMPLE PROBE LEVEL DETECTOR ERROR T (aa) 样本针液面监测错误
SAMPLE PROBE INTERNAL WASH DISABLED T (aa,bb,cc) 样本针内壁冲洗无效 REAGENT PROBE UP/DOWN ERROR T (aa,bb,cc) 试剂针上下错误 REAGENT PROBE ROTATION ERROR T (aa,bb,cc) 试剂针摆动错误 REAGENT REF. ROTATION ERROR T (aa,bb,cc)
REAGENT DISPENSER ERROR T (aa,bb,cc) 试剂分配错误
REAGENT PROBE LEVEL DETECTOR ERROR T (aa) 试剂针液面监测错误
REAGENT PROBE INTERNAL WASH DISABLED T (aa,bb,cc) 试剂针内壁冲洗无效 MIX UP/DOWN ERROR T (aa,bb,cc) 搅拌器上下错误 MIX ROTATION ERROR T (aa,bb,cc) 搅拌器旋转错误 MIXING ERROR T 搅拌器错误
CUVETTE WASH UNIT ERROR T (aa,bb,cc) 冲洗站单元错误 CUVETTE WASH DISABLED T (aa,bb,cc) 冲洗站无效
CUVETTE WHEEL ROTATION ERROR T (aa,bb,cc) 反应盘旋转错误 PHOTOMETER ERROR T (aa) 光度计错误 LBF RACK EXIST $T
STRONG DRAIN TANK FULL 浓废液罐满 WEAK DRAIN TANK FULL 淡废液罐满 R1 REAGENT SHORT (aaaaa,bb) R1缺少 R2 REAGENT SHORT (aaaaa,bb) R2缺少
R1 REAGENT EMPTY (aaaaaaaaaa,bbbbb,cc,dd) R1空 R2 REAGENT EMPTY (aaaaaaaaaa,bbbbb,cc,dd) R2空 INCUBATION BATH TEMP. ERROR 反应水槽温度错误
SAMPLE EMPTY LEVEL DETECT (aaaaaa,bb,cc,ddddd-ee) 样品空 AUTOMATIC REPEAT BELT FEEDER JAM 自动重测皮带步进卡住 AUTOMATIC REPEAT RECEIVER JAM 自动重测接收卡住
SAMPLE PROBE STUFF SENSOR ERROR T (aa) 样本针堵塞传感器错误 STUFF SAMPLE DETECT (aaaaa,bb,ccccc-dd) 样本探测堵塞 DETERGENT A EMPTY 清洗剂A空 DETERGENT B EMPTY 清洗剂B空 ISE COVER OPEN ISE盖打开 STAT COVER OPEN 急诊盖打开
STAT SET OVER TIME 急诊设置超时
AUTO REPEAT RUN RACK DISABLED 自动重测运行架无效 MIRROR ROTATION ERROR T (aa,bb,cc) 棱镜旋转错误 R2 REAGENT EMPTY (aaaaa,bb,cc) R2试剂空 PRE DILUTION WATER SHORT 预稀释水少
PRE DILUTION WATER EMPTY LEVEL DETECT (aaaaaa,bb,cc) 预稀释水空 REAGENT TRANSPOSITION DISABLED (aa) 试剂转位无效 QC SAMPLE PROHIBITED 质控样本阻止
MEASURE RESTART DISABLE 测量重新开始无效
326832693301330233033304330533063307330833093310331133133314331533163351335233533354335533563357335833593360336133624001400240034004400540064008400940104011401240134014401540164017401840194020402140234024402540264027402840294030403140354036 REG. PROBE DETERGENT SHORT T (CLN-a,bb) 试剂针清洗剂少 REG. PROBE DETERGENT EMPTY T (CNL-a,bb) 试剂针清洗剂空 NO ISE 无ISE
ISE INITIAL ERROR (aa) ISE初始化错误 ISE MID STANDARD SHORT ISE内标液少 ISE BUFFER SHORT ISE缓冲液少 ISE REFERENCE SHORT ISE参比液少
ISE CLEANING SOLUTION SHORT ISE清洗剂少 ISE STANDARD L SHORT ISE低准液少 ISE STANDARD H SHORT ISE高标液少
ISE SELECTIVITY CHECK (Na) SHORT ISE选择性检查Na少 ISE SELECTIVITY CHECK (K) SHORT ISE选择性检查K少 ISE LOW DATA ISE数据低
ISE SAMPLE No. ILLEGAL PROCEDURE (aaaa) ISE编号程序不合法 ANL <- ISE COM. ERROR (aa,bb) ANL-ISE通讯错误
ANL <- ISE TEXT NOT RECEIVED (aa,bb) ANL-ISE无接收文本 ANL <- ISE COM. RECEPTION ERROR (aa,bb) ANL-ISE通讯接收错误 ISE <- ANL COM. ERROR (aa,bb) ISE-ANL通讯错误
ISE <- ANL TEXT NOT RECEIVED (aa,bb) ISE-ANL无接收文本 ISE SEQUENCE ERROR T ISE顺序错误
ISE SYNC SIGNAL ERROR T (aa,bb,cc,dd,ee,ff,gg) ISE同步信号错误 ISE A/D ERROR T (aa) ISE A/D转换错误 ISE TEMP. ERROR (aa) ISE温度错误
ISE BUFFER DISPENSER ERROR T (aa) ISE缓冲液分配错误 ISE MID STANDARD PUMP ERROR T (aa) ISE内标液泵错误
ISE SAMPLE ASPIRATION PUMP ERROR T (aa) ISE样本吸取泵错误 ISE SAMPLE MIXER ERROR T (aa) ISE样本混合错误
ISE D-POT OVERFLOW SENSOR ERROR T (aa) ISE样本池溢流传感器错误 ISE -> ANL COM. RECEPTION ERROR (aa,bb) ISE-ANL通讯接收错误 NO SAMPLE CUP (aaaaa-bbbbb-cc) 无样本杯 SAMPLE NOP (aaaaa-bbbbb-cc) 样本无操作
SAMPLE ID NOT FOUND (aaaaa,bbbbb,cc) 样本编号没有找到
REPEAT SAMPLE ID NOT FOUND (aaaaa-bbbbb-cc) 重测样本编号没有找到 REPEAT SAMPLE NOP (aaaaa-bbbbb-cc) 重测样本没有操作请求 ILLEGAL SAMPLE ID (aaaaa-bbbbb) 样本编号非法 BROKEN LABEL (aaaaa-bbbbb-cc) 中断列表
REPEAT BROKEN LABEL (aaaaa-bbbbb-cc) 重测列表中断
SAMPLE ID READ ERROR (aaaaa-bbbbb-cc) 样本编号读取错误
REPEAT SAMPLE ID READ ERROR (aaaaa-bbbbb-cc) 重测样本编号读取错误
MEASURE COMPLETED FOR THE READ SAMPLE ID (aaaaa-bbbbb-cc) 读取的样本编号测试完成 CALIBRATION FACTOR RANGE OVER (aaaaa) c 定标因数超过范围 CALIBRATION FACTOR RANGE UNDER (aaaaa) c 定标因数低于范围 CALIBRATION OD RANGE OVER (aaaaa) b,c 定标OD超过范围 CALIBRATION OD RANGE UNDER (aaaaa) b,c 定标OD低于范围 CALIBRATION ERROR (aaaaa) c 定标错误
QC DATA RANGE OVER (aaaaa,bb,ccccc,d) 质控数据超过范围 QC DATA RANGE UNDER (aaaaa,bb,ccccc,d) 质控数据低于范围 QC DATA CHECK ERROR (aaaaa,bb,ccccc,d) 质控数据检查错误 PANIC VALUE (aaaaa,bbbbb,cc,dd) 危机值 PHOTOCAL DATA ERROR 光度校正数据错误 REAGENT REF. TEMPERATURE LOW 试剂温度低 REAGENT REF. TEMPERATURE HIGH 试剂温度高
INCUBATION BATH TEMPERATURE HIGH 反应槽温度高 INCUBATION BATH TEMPERATURE LOW 反应槽温度低
STAT SAMPLE MEASURE START CANCELED 开始急诊样本测量取消 DPR <-> ANL COM. START TIMEOUT DPR-ANL通讯开始超时 DPR <-> ANL COM. TIMEOUT (aa) DPR-Anl通讯超时 ILLEGAL PARAMETER (aaaaa,b,c,d,e) 项目非法 NO SAMPLE REQUISITION (aaaaa) 无样本申请 DATA WRITE DISABLED (aaaaa) 写数据无效
404040414042405140524053410141024103410441054106410741089001900290039004900591419143917391749176923192329241929192929401940294039404940594069407940894099410941194129413941494159416914794189419942094219422942394249425942694279428942994309431 SAMPLE BLANK CORRECTION WITHOUT COLOR DATA (aaaaa-bbbbb-cc ddddd eeeee) 样本空白校正不使用颜色数据 SAMPLE BLANK CORRECTION WITHOUT BLANK DATA (aaaaa-bbbbb-cc ddddd eeeee) 样本空白校正不使用空白数据 STAT SAMPLE MEASURE START ERROR 急诊样本测量开始错误 REPEAT SAMPLE NO CUP (aaaaa-bbbbb-cc) 重测样本无杯子 ILLEGAL REPEAT SAMPLE ID (aaaaa) 重测样本编号非法 MAXIMUM NUMBER OF SAMPLE (aa) 样本号码最大 NO STAT CUP (CALIBRATION NO. aa bb) 无急诊杯 NO STAT CUP (CONTROL NO. aa bb) 无急诊杯
STAT CAL/QC DUPLICATE ID (aaaaa) bb 急诊、质控、标准品一样的编号 STAT CAL/QC ID READ ERROR (aa) 急诊、质控、标准品编号读取错误 NO STAT CUP (RB) 无急诊杯
INVALID STAT CUP (CALIBRATION NO. aa) 急诊杯无效 INVALID STAT CUP (CONTROL NO. aa) 急诊杯无效 INVALID STAT CUP (RB) 急诊杯无效 LOGIN [aa] 登录 LOGOUT [aa] 注销
TEMPORARY LOGIN [aa] 临时登录 MENU [aa] 菜单
MENU [aa] EXIT 菜单 退出 Hard Copy Error 硬盘复制 PRINTER BUSY 打印机忙
SECONDARY PRINTER BUSY 备用打印机忙 PRINTOUT ERROR 打印输出错误
SECONDARY PRINTER PRINTOUT ERROR 备用打印输出错误 PASSWORD ERROR [aa] 密码错误
NEW PASSWORD IS NOT IDENTICAL WITH CONFIRMATION PASSWORD 新密码校验密码不一致 PRINTER BUSY 打印机忙 Database Inf [aa]
Database Error [aa] 数据库错误 Access is denied 接入拒绝
This account is currently disabled and cannot be logged on to 当前账号无效，不能登录 The user’s account has expired 用户账号过期
Some user account restriction has prevented successful authentication 用户账号限制相同 Attempt to create file that already exists 尝试创建的文件已经存在
The system is currently running with the last-known-good configuration 当前系统运行前一次正常启动的 The storage control blocks were destroyed 存储控制失败 The specified user name is invalid 指定用户名称无效
The configuration registry database is damaged 配置登记数据库损坏 The configuration registry key is invalid 配置登记索引无效 The requested resource is in use 请求资源使用中
Cannot complete function for some reason 同样的理由不能完成 The directory or file cannot be created 不能创建文件或文件夹
The configuration registry key cannot be opened 配置登记索引不能打开 The configuration registry key cannot be read 配置登记索引不能读取 The configuration registry key cannot be written 配置登记索引不能写入
An attempt was made to create a stable subkey under a volatile parent key 尝试建立子索引 Data error 数据错误
The database specified dose not exist 指定数据库不存在 The directory is not empty 文件夹不空
The directory name is invalid 文件夹名称无效
The disk structure is damaged and nonreadable 磁盘结构损坏不能读取 There is not enough space on the disk 磁盘空间不足
While accessing the hard disk, a disk operation failed 访问硬盘时，操作失败
While accessing the hard disk, a recalibrate operation failed 访问硬盘时，重定标操作失败
A hard disk controller reset was needed, but even that failed 硬盘控制器必须复位，偶校验失败 An extended error has occurred 发生扩展错误
The file or directory is damaged and nonreadable 文件或文件夹错误不能读取 The system cannot find the file specified 系统不能找到指定文件 The file name or extension is too long 文件名或扩展名太长 The disk is full 磁盘满
9432 Reached End Of File 文件到头
This operation cannot be completed due to on-disk data structure corruption 操作不能完成，因为在盘数9433
据损坏
9434 The system cannot find the specified drive 系统不能找到指定的驱动器9435 The flag passed is incorrect 标志通过错误9436 The flags are invalid 标志失败
9437 The user account has time restrictions and cannot be logged onto at now 用户账号时间限制，不能现在9438 The parameter is incorrect 参数不正确
9439 The specified network password is incorrect 指定网络密码不正确9440 The format of the specified password is invalid 指定密码格式错误9441 The printer command is invalid 打印命令不正确9442 The printer name is invalid 打印机名不正确
9443 The user account is restricted and cannot be used to log on 用户账号限制，不能登录9444 The attempted logon is invalid 尝试登录失败
9445 The global filename characters * or ? are entered incorrectly 文件名存在*或？符号，输入不正确9446 An attempt was made to move the file pointer before the beginning of the file 文件头尝试移动文件头9447 System could not allocate required space in a registry log 系统不能分配登记日记空间9448 The drive is not ready 驱动器没有准备好
9449 The system cannot open the specified device or file 系统不能打开指定文件或设备
The I/O operation was aborted due to either thread exit or application request I/O操作失败，只能关闭9450
进程或申请
9451 The printer is out of paper 打印机却纸
9452 File waiting to be printed was deleted 删除等待打印文件9453 The printer queue is full 打印队列满9454 The registry is damaged 档案损坏
9455 The registry initiated an I/O operation that had an unrecoverable failure I/O登记不可预料失败9456 The drive cannot locate a specific area on the disk 磁盘不能驱动指定的扇区
9457 The file pointer cannot be set on the specified device or file 文件点不能设置指定的设备或文件9458 Insert the disk for drive 1 在驱动器1插入磁盘
9459 The credentials supplied conflict with an existing set of credentials 资格冲突
9460 The process cannot access the file because it is being used by another 文件处理失败，另一个程序正在9461 The system cannot open the file 系统不能打开文件
9462 The disk media is not recognized. It may not be formatted 系统媒体不能确认，没有格式化9463 The media is write protected 写保护9471 File genric Error [%s] 文件错误9472 File not found [%s] 文件没有找到9473 Bad pathname [%s] 路径名不正确
9474 Too many open files [%s] 打开文件太大9475 File access denied [%s] 文件决绝读取9476 Invalid File handle [%s] 文件句柄无效
9477 Can’t remove current directory [%s] 不能移动当前目录9478 Full directory [%s] 目录满
9479 Bad seek pointer [%s] 搜寻指针失败
9480 File Hardware I/O Error [%s] 文件硬件I/O错误9481 File sharing violation [%s] 文件共享失败9482 File lock violation [%s] 文件锁失败9483 File disk full [%s] 文件盘满9484 File end of file [%s] 文件结束
因篇幅问题不能全部显示，请点此查看更多更全内容